Basic Knowledge And Examples Of Pattern Design For Skirts [Figure]

The simplest way to design a skirt is to divide the basic form of a two piece half skirt into several parts.

"

Usually, the skirt prototype is a simple half cut.

。

But because it is made of paper, it can be folded and used.

The same pattern can be used for the front and rear centerlines of the four pieces of skirt. The front and back pieces are divided into two parts.

-

Or the same basic pattern, 4 pieces will be further folded to get 8 pieces; again the same fold, you can make 8 pieces into 16 pieces.

The prototype of the skirt can be divided into 6 pieces, which can be further divided into 12 pieces.

6 piece skirts are usually called "Apron".

This is a familiar style that can be made from it.

A variety of skirts.

In principle, each basic skirt type (standard skirt, straight skirt or full round skirt) can be divided into any number of cutting pieces, which can be the same or different.

If we make full use of the "line" or the basic type of change, we can get quite a lot of styles.

In fact, some shape lines are more suitable for multi chip designs.

For example, the molding line of full round skirt is warped outside.

Others are suitable for skirts with less cutting.

The style of the skirt is varied through slices, and the addition of loose weight between the cutting pieces can further increase the style of the skirt. The way of changing the skirt pattern also includes changing the use of the fabric texture, such as the skirt with a skew or cross direction.

Add all buttocks to all shapes and sizes of skirts, as well as many other specific cutting methods.

Example: simple multi piece skirt (see photo)

Style A 4 skirt, the front middle stitch is replaced by the buttons along the front centerline, so there is a need for a door (at least 3~4cm).

At the beginning of the picture, place the original position at the edge of the paper 4cm, leaving the width of the door open.

The welt can be single autocratic or linked to the front piece. The noodles should be at least 4cm more than the width of the door, that is, the buttonhole should be 7~8cm.

Usually, the welt is only cut on the fabric, like the turning angle, and does not need to be included in the cutting of the pattern.

Because this is a full round skirt, so it is used for one-piece skirts or "

The side stitch will have less savings when it comes to skirts.

In order to make the waist fit, if necessary, add a small province on the back center line. If it is to make a dress skirt, then there can be no provincial road, and all sutures should be straight lines, and the prototype is only suitable for the dress body.

The direction of the straight yarn is indicated on the pattern (SG).

Because the front piece has buttonholes, the center line should be straight before, and the rear piece should be straight from the middle axis of each piece, because this will increase the draping feeling of the skirt.

Generally, the posterior middle suture is almost straight, unless sometimes it is inclined to make the contour line more balanced.

Spread evenly around the body, but not at the center line, but outward at the side seam. This will happen if the centerline is straight.

The style B 8 piece skirt is made by cutting 4 pieces of skirt into two halves from the middle.

First, draw the front and back parts of the prototype skirt prototype, then fold each piece as if it were a straight yarn to mark.

Sometimes a small part can not be fully folded, but it doesn't matter.

The 1/4 round skirt prototype is also used in this type.

It uses the advantages of the prototype skirt prototype, that is, having a standard geometric shape, not necessarily a part of the circle.

The widened bottom pendulum (over the original 160cm) can start from the hip line or the lower point (the dotted line).

Each skirt is still straight in the middle.

The pattern C divides each piece of 6 skirts into twelve pieces.

In fact, only the front and rear sides are used, because the front and back pieces are half sided.

Since it is a fully round skirt, a small province should be provided for the tight waist of the skirt.

The center of the skirt is straight yarn.

This type of skirt has a low swing width of about 2.45m, but

The number of 12 stitches is =24, so the width of each piece is generally small, that is, 3~4cm.